Mobiles Secret Codes

Mobiles Secret Codes _
Samsung SGH-600 Unlock Codes

*#06# : Show IMEI
*#9999# : Show Software Version
*#0837# : Show Software Version (instructions)
*#0001# : Show Serial Parameters
*#9125# : Activates the smiley when charging.

*#9998*228# : Battery status (capacity, voltage, temperature)
*#9998*246# : Program status
*#9998*289# : Change Alarm Buzzer Frequency
*#9998*324# : Debug screens
*#9998*364# : Watchdog
*#9998*377# : EEPROM Error Stack - Use side keys to select values. Cancel and ok.
*#9998*427# : Trace Watchdog
*#9998*523# : Change LCD contrast - Only with version G60RL01W
*#9998*544# : Jig detect
*#9998*636# : Memory status
*#9998*746# : SIM File Size
*#9998*778# : SIM Service Table
*#9998*785# : RTK (Run Time Kernel) errors - if ok then phn is reset, info is put in memory error.
*#9998*786# : Run, Last UP, Last DOWN
*#9998*837# : Software Version
*#9998*842# : Test Vibrator - Flash the screenligth during 10 seconds and vibration activated.
*#9998*862# : Vocoder Reg - Normal, Earphone or carkit can be selected
*#9998*872# : Diag
*#9998*947# : Reset On Fatal Error
*#9998*999# : Last/Chk

*#9998*9266# : Yann debug screen (=Debug Screens?)
*#9998*9999# : Software version

If the up Codes doesn't work, you should change *#9998* to *#0. i.e. *#9998*523# change to *#0523#. An other thing that will help is to remove your SIM card. *0001*s*f*t# : Changes serial parameters (s=?, f=0,1, t=0,1) (incomplete)
*0002*?# : unknown
*0003*?# : unknown

SP-unlock SGH-600 (and also SGH-Sgh-600)
*2767*3855# : Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!! )
But also changes IMEI to 447967-89-400044-0. (Doing this is illegal)

*2767*2878# : Custom EEEPROM Reset

*These codes have been tested with version FLD_2C6 G60SB03X of Samsung SGH-600

---------------------------------------------

SGH600/2100DB

IMEI number: * # 0 6 #

Software version: * # 9 9 9 9 # or * # 0 8 3 7 #

Net Monitor: * # 0 3 2 4 #

Memory reset (removes SIMLOCK!!!): *2767*3855# (works only on older versions)

Memory reset CUSTOM: *2767*2878# (works only on older versions)

Change dispplay contrast: * # 0 5 2 3 #

Memory info: * # 0 3 7 7 # or * # 0 2 4 6 #

Battery status: * # 9 9 9 8 * 2 2 8 #

Change sound of alarm: *#9998*289#

Vibra test: *#9998*842#


----------------------
Samsung Reset Codes
You can try these in case you downloaded corrupted or incompatible Java midlets or other media, which are causing problems with the phone.

1.
*2767*JAVA# Java Reset and (Deletes all Java Midlets)
2.
*2767*MEDIA# Reset Media (Deletes All Sounds and Pics)
3.
*2767*WAP# Wap Reset
4.
*2767*CUST# Reset Custom EEPR0M
5.
*2767*FULL# Reset Full EEPR0M (Caution)
6.
For example : *2767*JAVA# would be keyed in as *2767*5282#

Note : Not all codes will work with SGH-C100.

Other Samsung Codes

1.
*#06# IMEI code
2.
*#9998*4357# Help Menu
3.
*#9998*5282# Java menu (GRPS/CSD settings for JAVA server)
4.
*#9999#0# Monitor Mode
5.
*#9999# or *#9998*9999# Software Version
6.
*#8888# or *#9998*8888# Hardware Version
7.
*#9998*746# or *#9998*0746# or *#0746# Sim Infos
8.
*#9998*523# or *#9998*0523# or *#0523# Display Contrast
9.
*#9998*842# or *#9998*0842# or *#0842# Vibration On (until you push OK)
10.
*#9998*289# or *#9998*0289# or *#0289# Buzzer On (until you push OK)
11.
*#9998*288# or *#9998*0288# or *#0288# Battery & Field Infos
12.
*#9998*377# or *#9998*0377# Error log
13.
*#9998*778# or *#9998*0778# or *#0778# Sim Service table
14.
*#9998*782# show date and alarm clock
15.
*#8999*638# show network information
16.
*#9998*5646# change operator logo at startup
17.
*#9998*76# production number
18.
*#9998*968# view melody for alarm
19.
*#9998*585# Non-Volatile Memory (NVM)
20.
*#3243948# Digital Audio Interference Off
21.
*#32436837# Digital Audio Interference On


SAMSUNG T100 SECRET CODES
============================
*#06# -> Show IMEI
*#9999# -> Show Software Version
*#0001# -> Show Serial Parameters

*2767*3855# -> Full EEPROM Reset ( THIS CODE REMOVES SP-LOCK!!!! but also change IMEI to 447967-89-400044-0, you must use CHGIMEI to restore it)

*2767*2878# -> Custom EEEPROM Reset
*#8999*228# -> Battery status (capacity, voltage, temperature)
*#8999*246# -> Program status
*#8999*289# -> Change Alarm Buzzer Frequency
*#8999*324# -> Debug screens
*#8999*364# -> Watchdog
*#8999*377# -> EEPROM Error Stack
*#8999*427# -> Trace Watchdog
*#8999*523# -> Change LCD contrast
*#8999*544# -> Jig detect
*#8999*636# -> Memory status
*#8999*746# -> SIM File Size
*#8999*778# -> SIM Service Table
*#8999*785# -> RTK (Run Time Kernel) errors
*#8999*786# -> Run, Last UP, Last DOWN
*#8999*837# -> Software Version
*#8999*842# -> Test Vibrator
*#8999*862# -> Vocoder Reg
*#8999*872# -> Diag
*#8999*947# -> Reset On Fatal Error
*#8999*999# -> Last/Chk
*#8999*9266# -> Yann debug screen (=Debug Screens?)
*#8999*9999# -> Software version


SAMSUNG V200 SECRET CODES

v200 Unlock Code-> *2767*7822573738#
*#9324# Netmon (press the hangup key to exit)
*#9998*JAVA# Edit GPRS/ CSD settings (S100 Only)
*#9998*Help# Help screen/ List of codes
*#9998*LOGO# Change operator Logo
*#9998*RTC# RTC Display
*#9998*Bat# Battery Status
*#9998*Buz# Turns Buzzer ON
*#9998*Vib# Turns Vibrator ON
*#9998*LCD# LCD Contrast
*#9998*9999# Softwre Version
*#9998*8888# Hardware Version
*#9998*377# NVM Error Log (?????)
*#9998*NET# SIM Network ID
*#9998*778# SIM Serv. Table
*#9998*SIM# SIM Info
*#9998*PN# Production No.
*#9998*968# Reminder Tune
*#9998*NVM# Displays Non-Volitile Memory Status
*#9999*C# ???????????????????
*#06# Displays phones I**I No.
***/// ***/// NOTE /// *** RED COLOR , they appear serious !!! Use at
own risk !!!
*#9998*2576# Forces SIM Error
*#9998*DEAD# Forces Phone Crash
*2767*MEDIA# Resets the medis on the phone (deletes all downloaded
pics/tones)
*2767*FULL# Resets the EEPRON *DANGEROUS*
*2767*CUST# Resets the Custom EEPRON
*2767*JAVA# Resets JAV downloads (deletes all downloaded midlits)
*2767*STACKRESET# Resets Stack
*2767*225RESET# ????????????????? * Dangerous *
*2767*WAP# Resets WAP Setting & Deletes Favorites

SAMSUNG A800 SECRET CODES

The universal unlock code is *2767*637# do this with out your sim in
By default, the firmware (software) for x600 only receives java
apps and other applications like stuff by serial port.
but even for it, you have to enable the serial port, which also
causes
the closing of all other ports, even the IrDA too :-( ..
well, guess what, i have very good news for you,
do you know, you can increase the sound level,
the sound level for tones, speaker fone, etc,
can be increase even then if it is at max (level 4)
you still can do it,
just follows the instructions!

**************** HERE WE GO **************
Enter the following code:
*#8999*8378#
(You'll be shown menu, then ...)
then go to:
"H/W test"
then go to:
"Audio Settings"

then go to:
"Melody Gain"

There will you see a number.
there are five (5) Melody Levels" of it.
(and currently, you are at level 1 and after
pressing the "save" button, you will move to
level 2 and so on .........................)
you have to change the values of all the levels.
and as the resultant, it will give increase the
melody sound!, your tones will more louder,
even more louder then the max. ringing volume.
the level wise numbers are: (as its my setting :-) )

Melody Level 1: 13
Melody Level 2: 17
Melody Level 3: 18
Melody Level 4: 25
Melody Level 5: 31
you even can make your own combinations of level wise
sounding numbers that can change the sound level!.

if your combination cause more louder sound level,
then mine,
then do share it with the group! ... :-)
meanwhile, try my figured-out combination!

************ CAUTION ************
if anything goes wrong,
then you can apply the master reset code,
that will NOT delete anything, ANYTHING from your
cell fone, but set each and eveything to its
default/standard setting ...
(likes, factory settings :-) )
the master reset code is:
#*7728#

#########################################
I take no responsibility of these codes are working or not,
or its effects on your cell fone
but i have tried these codes on my cell fone.
and i bet, nothing goes wrong,
but even then of my words, be carefull!,
#########################################
The code: *#8999*8378#
as i regarded it a informative code,
will tell you each and everything about your cell fone.
and in the "H/W test",
there are lot of other Audio settings,
each of them having five (5) levels,
you can change the combination, but before doing anything,
do write the defult number sequence to some place so that
you'll be then able to invert it again! .. :-) ...
#*2558# - Time ON
#*2527# - GPRS Switching Set to class {4/8/9/10}
#*4263# - Handsfree Mode: ACTIVATED
#*53696# - [Java dnload] WAPSAR mode
#*536961# - WAPSAR enable HTTP disable
#*536962# - HTTP enable WAPSAR disable
#*536963# - SERIAL enable Others disable
#*5663351# - [Phone Model] SAMSUNG SGH-X100
#*6420# - Mic off
#*6421# - Mic on
#*7632# - Sleep mode
*#8999*523# - Main LCD Brightness
*#8999*3825523# - (?) External display
*2767*3855# - Full EEPROM reset(Reset all type of locks)also you'll
lose pictures and java not melody
Remove camera sound:
On main screen type:
*#8999*8378# --> Test mode
H/W test
Audio Settings
Melody Gain
Then replace 6 by 0, it'll show 12 but it's OK
Press back until main screen
Then press key volume to minimum and let's try !!! no more sound
tip by C-Quest

*2767*688# resets the phone
Thats all!!!!!!!!!!!!!!!



--------------------------------------------

Activate net monitor: (pause means * holded until you see square)

[pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]

Deactivate:

[pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]

This option might not work with some versions of phones' software.

When you press OK you will have access to 3 additional menu options

1) Active cell

Displays active channel and allows to choose between
RxLev, RxLevAM, NCC, BCC, MSTxPwr i C1.

During a call you can see:
RxLev, RxLevFull, RxLevSub, RxQualFul, RxQualSub, Timeslot, TimeAdv, PwrLev

During a phone call you can see type of negotiation SDCCH
(Standalone Dedicated Control CHannel) takes place.
It can be: SDCCH8 or SDCCH4 .

2) Nearest cell:

You can view nearest cells (1 - 6) and their position.

3) System parameters

Displays : Combined, AcsClas, MCC, MNC, LAC, CellID, T3212, BS-PA-MFRM i XZQTY.

During a call you can see: Combined, DTX, MCC, MNC, LAC, CellID

Explanation of names showed on display

* RxLev: Power of incomming signal (dB)
* RxLevAm: Threshold value in dB, then it switches to other cell
* BCC: Broadcast Color Code Allows to see base stations transmitting on the same frequency.
* NCC: Network Color Code - National code of GSM operators GSM.
* C1: Space in dB from upper level at which it switches to other cell
* RxLevFull - Value of Cl parameter during continuous transmission.
* RxLevSub - Value of Cl parameter during non-continuous transmission.
* RxQualFull - Error bit rate measured for continuous transmission
* RxQualSub - Error bit rate measured for non-continuous transmission
* Timeslot - Time Slot Number. Number of frequency channel, description of time crack
* TimeAdv - Distance from transmitter in km. Multiply factor of results is 0,547
* PwrLev - Radiated power level
* MCC: Mobile Country Code - 260 = Poland
* MNC: Mobile Network Code - 01=PLUS GSM 02=ERA GSM, 03=IDEA appears after MCC.
* CellID: Cell ID

Power level 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
dBm 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13
Wats 16,0 12,8 8,0 5,2 3,2 2,0 1,3 0,8 0,5 0,32 0,2 0,13 0,08 0,05 0,03 0,02

Codes work with following software versions
TX770 5.3 / 2.3
6200 1.5 / 1.7
7500 5.3 / 2.1 , 6.0 / 2.1 , 6.3 / 2.3
8200 1.3 / 1.9 , 1.5 / 1.7 , 1.6 / 1.7 , 1.6 / 1.9 , 3.1 / 1.9




----------------------------------------------

S4:

Monitor Mode - how to activate:

Press left soft-key, then 9 (SET UP) 8 (Phone Status). You will see IMEI number, then press left soft-key and in order 7684666 and red phone at the end (monitor mode has been activated). To read information from Monitor Mode - press left soft-key, then 5 (GSM SERVICE) and 6 (Monitor). Monitor mode turns off when you switch off the phone. You must activate it again if you want.


How to see date of software:

Press left soft-key, then 9 (SET UP) 8 (Phone status). You will see IMEI number, then press twice left soft-key, 98, left soft-key, 7684666, red phone (activates Monitor Mode), left soft-key, 56 (turns on Monitor Mode), left soft-key, 98, left soft-key, 7684666, hang up (red phone) >abck to "normal" and then left soft-key, 56.

S6, S8:
If you add to phonebook under 'own phone number' +12022243121 with namez (for example MMI), then you will see something :)



S10, E10:

In phonebook enter +12022243121 as your own phone no. You will see a picture with sun, two palms and greetings.

S15e:

Monitor Mode:

Code: *#7436267*8378# (*#SIEMENS*TEST#)
Hold red phone button until it code disapears.
Menu 3.3.4 Choose frequency.
Menu 3.3.4.1 Automaticaly.
Menu 3.3.4.2 Choose GSM-900
Menu 3.3.4.3 Choose GSM-1800

Menu 10.1 MS info
Menu 10.2 Soft date
Menu 10.2.1 Software version.
Menu 10.2.2 EEProm version.
Menu 10.3 Tst and product info.
Menu 10.3.1 Handware data.
Menu 10.3.2 Date of manufacture
Menu 10.3.3 Service date
Menu 10.3.4 Date of repair.

S25:

Enhanced Full Rate
*#3370# turns on
#3370# turns off

Haft Rate Mode
*#4720# turns on
#4720# turns off.

Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish

How to change PIN2?
**04*old PIN2*new PIN2*new PIN2#

What is my software version?
Menu 8-8-2 press left-softkey when you see IMEI number, or *#06# and then green phone button and then press left soft-key.

How to extend battery life:
IrDA - turn on only when you need.
Turn off automatic network search (6-3)Turn off Vibration alarm.

C25:

Languages:
*#0000#+green phone - choose automaticaly
*#0001#+green phone - English
*#0030#+green phone - Greek
*#0031#+green phone - Netherlands
*#0032#+green phone - French
*#0034#+green phone - Spanish
*#0039#+green phone - Italian
*#0049#+green phone - German
*#0090#+green phone - Turkish

How to change PIN:

**04*old PIN*new PIN*new PIN#

How to check simlock status
*#0606# and then press left soft-key, you will see strange characters, then text ("brak blokad"). If you see for example 260-02, it means the phone is locked to Era GSM. In older models you can use *#06# and see the same information after clickin on left key (you will see IMEI and software version).



------------------------------------------------------------------------------------------------------------------------------

Philips DIGA phones:

Blocking list *#3333*#
Time connected *#2558*#
Flags,something *#3377*#
Security code *#7489*#

Philips FIZZ phones:

IMEI code *#06#
SW info *#8377*#
Security code *#1234*#

Philips SPARK phones:

IMEI: *#06#

Philips GENIE phones:

*#06# IMEI number
*#2254*# Status register: C, BS, RR, MMI, CREAT.
*#2255*# activate and deactivate the "DEBUG CALL"-Mode; when activated, make a call to a busy line an the phone will display some hex-codes on the display
*#2558*# the time in days,hours and minutes you are connected to the net
*#2562*# not clear; the phone reconnects to the net
*#2565*# not clear; warmstart
*#3333*# (NO) BLOCKING - list (15 items)
*#2377*# "BEER": not clear, the phone waits a random time and reconnects to the net
*#3377*# Init, Flags, SIM LCK
*#3353*# resets the (NO) BLOCKING - list
*#7378*# Name, Length, SIM phase
*#7489*# SECURITY CODE
*#7693*# activate and deactivate the SLEEP MODE (when deactivated the battery will go down!)
*#7787*# SPURIOUS INTERRUPT
*#7948*# SWITCH OFF
*#8463*# Some information about the SLEEP MODE: Wake, Sleep Req., Sleep

-----------------------------------------------------------------

IMEI

*#06#

CD5
*#simlock# - shows simlock status

Date of software

Remove sim card, enter *#06# and press [left softkey]

Monitor Mode

To activate Monitor Mode you should press in following order:

Menu
9 (Phone Options)
7 (Phone Status)
left MENU key
7684666
Red HandSet key


Authors

- To see surnames of this phone's authors you should:
- Enter phonebook
- Enter menu "own phone no."
- Enter as your own phone number: +12022243121
- OK

SONY CMD-Z1

*#8377466# - check software version

Sony CMD-C1


IMEI number: * # 0 6 #
Software version: #8377466#






-------------------------------------------------------------------

NOKIA

Nokia Codes Tips and Tricks



To check the IMEI (International Mobile Equipment Identity) Type-

*#06#

Information you get from the IMEI-

XXXXXX XX XXXXXX X

TAC FAC SNR SP



*

TAC = Type approval code
*

FAC = Final assembly code
*

SNR = Serial number
*

SP = Spare

To check the phones Software revision type-

*#0000#

Information you get from the Software revision-

V 05.31

18-02-99

NSE-3

*

1ST Line = Software revision
*

2ND Line = The date of the software release
*

3RD Line = Phone type

To enter the service menu type-

*#92702689# (*#WAR0ANTY#)

*

Serial number (IMEI)
*

Production date (MM/YY)
*

Purchase date (MM/YY) You can only enter the date once.
*

Date of last repair (0000=No repair)
*

Transfer user data to another Nokia phone via Infra-Red

Clock Stopping

To check weather your SIM Card supports clock stopping type-

*#746025625# (*#SIM0CLOCK#)



Revealing the Headphone and Car-Kit menus

Please note that if you do these next tricks, the new menus can't be erased without retoring the factory default settings. To do these tricks you need to short-circuit the pins on the bottom of the phone next to where you plug in you charger.



1. To activate the "Headset" menu, you need to short-circuit pins "3" and "4". After a short time the word "Headset" will be shown in the display. Menu 3-6 is now enabled.

2. To activate the "Car" menu, you need to short-circuit pins "4" and "5". After a short time the word "Car" will be shown in the display. Menu 3-7 is now enabled.



THE REBOOT TRICK

This should work on all software versions of the 6110.

1. Go to the Calendar (Menu-8)

2. Make a note or reminder.

3. Enter some text into the edit box.

4. Hold "Clear" until the whole text is cleared, then press "Back".

5. Press "0". The main screen will now be showing but a space appears on the screen. (you can't see it)

6. Enter 4 digits (e.g. 1234).

7. Use the down arrow to move the cursor to the left side of the numbers and the space (Down arrow twice).

8. Now enter 6 digits and press the call button.



Wait for a few seconds, the screen should start to flash and reboots. It should alsowork on other menus like the "Profiles" menu.



EFR CALL QUALITY

To activate EFR (Enhanced Full Rate) Enter the code-

*3370#

This improves call quality but decreases batterylife by about 5%

To deactivate it, Enter the code-

#3370#



THE JAMES BOND TRICK

If you short-circuit theleft middle and right pins on the bottom of the phone with all connections touching each other, the Nokia software hangs! The profile "Headset" will be activated. Before you do this just activate the "Automatic Answer" in the headset profile and set the ringing volume to "Mute". Now you can use your phone for checking out what people are talking about in a room. Just place it under a table in a room and call it. The phone receives the call without ringing and you can listen to what people are saying.



NETWORK MONITOR

There is a hidden menu inside your Nokia phone. If you want to activate it, you'll have to re-program some chips inside of your phone.

1.

Check your software version. You can only continue if you have v4.33, v4.73 or v5.24.
2.

Take apart the phone.
3.

De-solder the EEPROM (ATMEL AT 24C64).
4.

Read out the data with an EEPROM programmer and save it to a file (Backup).
5.

If you have v.33 or v4.73, change the address "03B8" from "00" to "FF".
6.

If you have v5.24 then change the address "0378" from "00" to "FF".
7.

Write the new data to the EEPROM and solder it back to the phone,
8.

Power on your phone and you should have "Netmonitor" enabled.

The Network Monitor gives you the following information.



*

Carrier number
*

MS RX Level in DBM
*

Received signal quality
*

MS TX power level
*

C1 (Path loss criterion, used for cell selection and reselection). The range is -99 to 99.
*

RTL (Radio link timeout).
*

Timeslot
*

Indication of the transmitter status
*

Information on the Network parameters.
*

TMSI (Temporary Mobile Subscriber Identity).
*

Cell identification (Cell ID, Number of cells being used).
*

MCC (Mobile country code)
*

MCN (Mobile network code)
*

LAC (Location area code)
*

Ciphering (On/Off)
*

Hopping (On/Off)
*

DTX (On/Off)
*

Discard cell barred information



CHECK SIM-LOCK

Note - If you bought your Nokia on UK Vodafone or UK Cellnet you do not need to check this because they both transmit on GSM900, and they don't lock the phones. However if you bought your phone on UK Orange or UK One2one your phone may be blocked. The reason is that they both transmitt on GSM1800. To make a call on GSM1800 you need what is known as a "Dual band" phone. A dual band phone is able to transmit on both GSM900 and GSM1800, so they lock the phones so you can't use it with any other network simcard. If you find that your phone is locked you can try different software to unlock it. (we havn't found one that works yet), or you can ask your service provider who will gladly exchange the 10 digit code for about £35.

This is how to check the status of the 4 different locks. Aslo don't try entering the wrong number, because after 3 times it will block the phone for good.



There are 4 different locks on your Nokia phone.

*

COUNTRY-LOCK
*

NETWORK-LOCK
*

PROVIDER-LOCK
*

SIMCARD-LOCK

The code to read out the sim-lock status of your phone is



#PW+(MASTERCODE)+(Y)#

*

# = DOUBLE-CROSS
*

W = PRESS "*" THREE TIMES
*

P = PRESS "*" FOUR TIMES
*

+ = PRESS "*" TWO TIMES
*

MASTERCODE = 1234567890
*

Y = NUMBER 1 TO 4

The master code is a secret code. The code has 10 digits, To read out the sim-lock status you can enter every combination you want!

"Y" Shows the status of the network-lock. Here you can enter a number from "1" to "4". The "4" is for the sim-card lock.



Try At Ur Own Risk...